How To Build A Classic curtilage Fence

gallery-1495640469-f7

We ll show you ways to create a fence, if you only need to stay out the neighbor’s dog, or to outline your personal landscape with slightly of subject aptitude.

Our lattice-top style makes a perfect privacy screen, however it will do way more. Erect many panels at the corner of your yard to make a secure parcel, or place them ahead of a pile or toolshed. Either way, you will be giving your back forty a welcome bit of sophistication.

MATERIAL WITNESS
We designed most of the fence with 3/4-in. No. two common pine. This wood can have knots, and it is a smart plan to seal the boards with a shellac-based sealer, like B-I-N, so that they do not bleed through the paint job. For the cap, lattice and splines, we tend to switched to 5/4 (1-1/8 in. thick) lumber and used choose grade to avoid the knots. The fence is meant to be designed inside, then assembled on-the-spot. The box posts and sandwiched panels build construction easy— simply make certain to check the drawing before you start.
MATERIALS LIST
KEY QTY. SIZE DESCRIPTION
FENCE PANEL
A four 3/8 x 1-1/8 x 77-5/8″ select-grade pine (lattice strip)
B nineteen 3/8 x 1-1/8 x 13-7/8″ select-grade pine (lattice strip)
C eight 3/4 x 2-1/2 x 82-3/8″ No. two pine (rail)
D four 3/4 x 3-1/2 x 11-5/8″ No. two pine (upper stile)
E four 3/4 x 3-1/2 x 46″ No. two pine (lower stile)
F one three/4 x 3 x 82-3/8″ No. two pine (divider)
G two 3/4 x 3-3/4 x 68-3/8″ No. two pine (endcap)
H one 3/4 x 3-3/4 x 83-7/8″ No. two pine (top cap)
I fifteen 3/4 x 5-3/8 x 51″ No. two pine (slat)
J fourteen 3/16 x 1-1/8 x 51″ select-grade pine (spline)
GATE
A four 3/8 x 1-1/8 x 35-1/8″ select-grade pine (lattice strip)
B nine 3/8 x 1-1/8 x 13-7/8″ select-grade pine (lattice strip)
C eight 3/4 x 2-1/2 x 39-1/4″ No. two pine (rail)
D four 3/4 x 3-3/16 x 11-5/8″ No. two pine (upper stile)
E four 3/4 x 3-3/16 x 44-1/2″ No. two pine (lower stile)
F one three/4 x 3 x 39-1/4″ No. two pine (divider)
G two three/4 x 3 x 66-7/8″ No. two pine (endcap)
H one three/4 x 3 x 40-3/4″ No. two pine (top cap)
I seven 3/4 x 5-1/2 x 49-1/2″ No. two pine (slat)
J half-dozen 3/16 x 1-1/8 x 49-1/2″ select-grade pine (spline)
POST
K two 3/4 x 5-1/4 x 73-1/4″ No. two pine (post side)
L two 3/4 x 3-3/4 x 73-1/4″ No. two pine (post side)
M four 5/8 x 1-1/8 x 6-3/4″ select-grade pine (cap trim)
N one 1-1/8 x 7-1/2 x 7-1/2″ select-grade pine (post cap)
O one 3-1/2 x 3-1/2 x 84″ pressure-treated (post core)
FASTENERS
P as reqd. No. twenty change of integrity plate
Q as reqd. 5/8″ brad
R as reqd. 6d galvanized finishing nail
S as reqd. 8d galvanized finishing nail
T as reqd. 11/4″ No. eight galvanized fh screw
U as reqd. 2″ No. eight galvanized fh screw
Misc : Waterproof glue; primer; shellac-based sealer; exterior wood filler; paint; 8-in. decorative hinge, Stanley No. 611043;11-in. heavy-duty thumblatch, Stanley No. 622044. Note: Quantities indicated are for one gate, one fence panel and one post.
1. TAKING STOCK
While painted pine was our selection, it does not need to be yours. At the low finish of the value spectrum is pressure-treated lumber, followed in increasing price by pine, cedar, redwood, mahogany and teak. These are all woods with some extent of resistance to weathering and decay, though pine depends on a decent paint job to survive the weather. Of course, costs vary with handiness, grade, size and specific species. for instance, western red cedar will price over doubly the value of northern white cedar. And at the high finish, teak will run over ten times the price of the No. two pine we tend to used.
2. PREP WORK

The first step is to tear all the stock to dimension, starting with the 3/8-in.-thick lattice strips. a transportable power saw can handle the work, however use a foothold guide to make sure uniform thickness. Prepare the 3/16-in. spline stock within the same manner. Then, crosscut all fence items to length. to make sure sq. cuts, guide your saw with a square control against the stock edge.

Prepare the lattice strips for assembly by marking the cross-strip locations. For speed and accuracy, clamp every panel cluster along and mark all the strips directly.

3. PANEL DETAILS

Join the lattice strips with 5/8-in. brads. If the assembly is not absolutely sq., merely pull it into form before sandwiching it between its 2 frames. Set the brads below the surface of the wood and fill with glazing putty or exterior wood filler. Plate joinery is that the quickest thanks to produce correct and fairly sturdy frame joints.

After cutting the slots at the ends of the items (C1, D1 and C2, D2 in our PDF plans), apply waterproof glue, be part of the elements ANd clamp for concerning an hour.

Place a frame over a lattice and secure it with 6d nails. Drive the nails concerning an in. so that they do not break through the skinny strips. Flip the panel over, support it on some spacers and nail the other frame, driving the nails flush. Then, end driving the nails on the primary aspect.

With all of the lattice assemblies designed, nail a divider (F1, F2) to the underside of every. Use a 3/16-in. slot cutter in a very router table to chop spline slots within the edges of the bottom-panel slats (I1, I2). you furthermore mght might do the work with serial passes on a table saw. Prime the splines (J1, J2), use them to affix the slats for one panel and lay the subassembly on the ground. do not glue the splines within the slat grooves, because the joints must be able to expand and contract.

Assemble the lower panels within the same manner because the lattice panels. Tack one frame to the slats, then flip the assembly over to secure the other frame. Then, drive all nails flush.

Stand a lower panel upright and place a lattice section on its prime edge. Drive nails at AN angle through the divider and into the highest rails of the lower panel.

Secure the endcaps (G1, G2) with 2-in. deck screws. Then, nail the highest (H1, H2) to the lattice panel rails.

4. POST BUILDING
Box posts be as a result of the peak of every post will be adjusted to level the fence once it’s in situ. confine mind that you simply could need to alter post lengths and build a stepped fence if your web site is gently diagonal. Before you build the boxes, prime the insides of the boards to safeguard against wet. Assemble the box elements (K, L) with 6d nails.

Cut 5/4 stock to size for the post caps and mark tips round the edges for the cap bevels. form the bevels with a plane. Then, use a bit and router table to chop the bevel on the cap trim (M).

5. ASSEMBLY
On-site construction are easier if you join the posts to the panels within the search, mark and variety the elements, and so break apart them. Use 1-1/4-in. screws driven through the endcaps (G1).

Mark and cut the notches within the gate endcaps (G2) therefore the hinges and latch hardware can sit flush against the gate rail surfaces. Use alittle carpenter’s saw to chop the notch edges and switch to a chisel to get rid of the waste. Attach the hinges to the gate and post, and so take away them till final assembly.

Slide a pressure-treated four x four post core four linear unit. into every post box. Secure with screws, however confirm that the heads are accessible therefore post heights will be adjusted on-the-spot. Prime and paint the bottoms of all panels, gates and posts. Once the fence is put in, these elements are tough to achieve. And, they are the foremost prone to wet infiltration.

, ,